2 max sway (typ) do not scale from this print w tfm-1xx-xx-x-s-xx no of positions all positions available -03 thru -50 -s: single row (use tfm-xx-s-xx-xx) lead style plating specifications -s: selective (use t-1r16-xx-s-xx) -f: flashed gold (use t-1r16-xx-f-xx) -p: gold flashed palladium nickel (use t-1r16-xx-p-xx) -l: light gold (use t-1r16-xx-l-xx) option -a: alignment pin (use tfm-xx-s-01-a) (not available with -wt option) (see fig. 5 sheet 2) -lc: locking clip (use lc-05-tm) (not available with -wt option) (see fig. 7 sheet 3) (see note 6) -p: pick and place pad (use ppp-15) (see fig. 6 sheet 2) (not available -03, -04 & -05 positions) -k: polyimide film (see fig. 3 sheet 2) (use k-500-300) -wt: weld tabs (use wt-25-07-t) (see fig. 4 sheet 2) (available on -05 thru -30 pos only) (not available with -a or -lc options) -tr: tape & reel (see sheet 3, tape and reel view) -sn: solder nail (use wt-27-03) (not available with -a, -lc, or -wt options) (see fig. 8 sheet 3) body specification -01: t-1r16-01-x-2 through hole -02: t-1r16-01-x-2 surface mount -03: t-1r16-10-x through hole .100 ref 2.54 + .025[.64])ref ((no. of positions x .050[1.27]) + .125[3.18])ref ((no. of positions x .050[1.27]) .065 1.65 .083 2.11 .105 ref 2.67 .175 ref 4.45 .050 ref 1.27 c 01 "a" "b" ref .018 0.46 .014 ref 0.36 - .050[1.27]) ((no. of positions x .050[1.27]) 2 max sway (typ) "a" "a" figure 1 (tfm-115-01-x-s-xx shown) .010 ref 0.25 .1635 ref 4.153 .2200 5.588 2 max toe (typ) 2 max toe (typ) section "a"-"a" "c" in-process c c c c c c * not released for production ** not tooled c * ** table 1 allowable coplanarity positions -03 thru -29 .004 max -030 thru -39 .006 max -40 thru -50 .008 max table 2 lead style body "a" "b" "c" -01 tfm-xx-s-xx-xx 0.075 [1.91] 0.133 [3.38] 0.4285 [10.884] -02 tfm-xx-s-xx-xx n/a 0.133 [3.38] 0.4285 [10.884] -03 tfm-xx-s-xx-xx 0.109 [2.77] 0.140 [3.56] 0.644 [16.36] sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 [.3] 2 .xxx: .005 [.13] .xxxx: .0020 [.051] material: .050 c.l. single row shrouded terminal strip by: tfm-1xx-xx-x-s-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. schmelz 8/21/2008 3 1 sheet scale: 1:0.4 insulator: liquid crystal polymer, color: black terminal: phosphor bronze f:\dwg\misc\mktg\tfm-1xx-xx-x-s-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. minimum pushout force to be 16 oz for terminals, 12 oz for weld tabs, and 8 oz for locking clips. 3. measured from bend. 4. .003[.08] maximum terminal burr. 5. .005 maximum height variation between any two pins. 6. due to the high amount of insertion force needed, the -lc option is not compatible with auto placement. samtec recommends manual placement for all assemblies with the -lc option. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision w
"b" "b" figure 2 surface mount (tfm-115-02-x-s-xx shown) (different as shown, otherwise same as fig. 1 (tol accum .005[.13] over 50 pos.) ((no. of positions x .050[1.27]) -.050[1.27]) 2 max sway (typ) 01 03 02 .225 - .000 + .005 5.70 0.000 + 0.127 flush to .005 max 0.12 .185 ref 4.70 90 7 0 2 max toe (typ) section "b"-"b" (see note 3) see table 1 "s" .216 .005 5.49 0.13 .021 .010 0.52 0.254 "r" figure 3 -k: polyimide film pad (tfm-115-02-x-s-k shown) note: r = overall length ref s = ((r - .216[5.49]) /2) .020[.51] .230 5.83 .010 0.25 ref (typ) +.263[6.68]) ref ((no of positions x .050[1.27]) + .154[3.91]) ((no. of positions x .050[1.27]) 2 max sway (typ) "d" "d" figure 4 -wt option (tfm-115-01-x-s-wt shown) (different as shown, otherwise same as fig. 1) tfm-xx-s-01-wt c .093 (typ) 2.36 .025 0.64 ref section "d"-"d" wt-25-07-t .045 ref 1.14 .050 1.27 ref + .075[1.91]) ((no. of positions x .050[1.27]) figure 5 -a option (tfm-115-02-x-s-a shown) (different as shown, otherwise same as fig. 1) r .025 0.64 .050 1.27 "e" "e" c l ppp-15 .375 9.53 ref "p" "m" figure 6 -p option (tfm-115-02-x-s-p shown) (different as shown, otherwise same as fig. 1) (pad to be positioned on c.l. as shown) c .175 4.45 ref section "e"-"e" c c c c note: m = (no. of positions x .050[1.27]) + .125[3.18] ref with -wt m = (no. of positions x .050[1.27]) + .263[6.68] ref p = ((m - .375[9.53]) /2) .020[.51] sheet of .050 c.l. single row shrouded terminal strip by: tfm-1xx-xx-x-s-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. schmelz 8/21/2008 3 2 sheet scale: 2:1 revision w f:\dwg\misc\mktg\tfm-1xx-xx-x-s-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
user direction of un-reeling pocket not detailed w .050 1.27 .010 ref 0.25 + .075[1.91]).002[.05] ((no. of positions x .050[1.27]) 2 max sway (typ) figure 7 -lc option (tfm-115-01-x-s-lc shown) (different as shown, otherwise same as fig. 2) tfm-1xx-02-s-lc c .056 ref 1.42 2 max sway (typ) c l lc-05-tm * * * packaging tube view notes: 1. use pt-1-24-11-09 tube and (2) tp-24 for -a, -wt, and -sn parts 2. use pt-1-24-03-09 tube and (2) tp-09 for -p-lc and -k option parts 3. load tube with 1st position in same direction as arrow pt-1-24-11-09 "f" "f" position 01 section "f"-"f" scale 1.25 : 1 (no of positions x .050[1.27]) + .255 ref +.175[4.45] (no. of positions x .050[1.27]) 2 max sway (typ) w "g" "g" wt-27-03-x figure 8 -sn option (tfm-110-02-x-s-sn shown) (different as shown, otherwise same as fig. 1) ** .026 ref 0.66 (2 plcs) .075 1.91 ref flush to .005 0.13 above section "g"-"g" scale 3 : 1 * inspect only when applicable with respect to assembly option tape and reel view ** not tooled sheet of .050 c.l. single row shrouded terminal strip by: tfm-1xx-xx-x-s-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing d. schmelz 8/21/2008 3 3 sheet scale: 2:1 revision w f:\dwg\misc\mktg\tfm-1xx-xx-x-s-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
